Dante AV Encoder/Decoder (D20 Series Transceiver)

Overview

Bolin’s D20 Series Dante AV transceiver device can be programmed as an encoder or a decoder. D20 Series is a single channel networked AV over IP transceiver that is fully compatible with Dante audio devices within a Dante ecosystem for HDMI sources up to 4K60Hz 4096 x 2160, with embedded audio and PTZ camera movement control via IP or IR pass-through. It provides audio and video streaming over a standard gigabit network and D20S/D20H models as decoders output baseband video, either HDMI or 12G SDI, to work in professional AV applications.

It features advanced high-quality YUV4:4:4, ProAV optimized JPEG2000 lossless video compression technology and HDCP 2.2 compliant achieves ultra-low latency with 100% audio video synchronization when paired using Dante AV encoder and decoder.

D20 Series Transceivers are encoder/decoder devices configurable via firmware update. It is part of the Bolin DanteAV camera/codec system, it delivers a high-performance virtual video matrix routing solution for presentation of multimedia, and live camera images, Dante 4k video content application such as demanding conference room and classroom applications.

    Key Features

  • DanteAV Module Imbedded Decoder

    Powered By DanteAV™ Module

    ■ Bolin D20 Series transceiver is powered by DanteAV™ module, it achieves lossless video and extremely low latency IP video streaming with video and audio synchronization.
    ■ Designed to seamlessly integrate into an existing Dante audio ecosystem, the D20 Series transceiver is managed using the Dante Controller Software with flexibility to independently route audio and video with sub-microsecond accuracy to minimize time alignment issues. More information about Dante AV

    ■ Bolin D20 Series transceiver is powered by DanteAV™ module, it achieves lossless video and extremely low latency IP video streaming with video and audio synchronization.
    ■ Designed to seamlessly integrate into an existing Dante audio ecosystem, the D20 Series transceiver is managed using the Dante Controller Software with flexibility to independently route audio and video with sub-microsecond accuracy to minimize time alignment issues. More information about Dante AV

  • Bolin-Dante-AV-System-Short-Diagram-w-1

    Dante Ecosystem Friendly

    ■ Instant compatibility with over 3000 existing Dante-enabled products.
    ■ Unified control of camera’s video and audio streams using familiar tools - Dante Controller Software.
    ■ No need to replace network infrastructure. Dante AV works with already installed, cost-effective 1Gbps network gear.
    ■ Uses Dante Controller and endpoints so you can easily click to check video and audio control routing.

    ■ Instant compatibility with over 3000 existing Dante-enabled products.
    ■ Unified control of camera’s video and audio streams using familiar tools - Dante Controller Software.
    ■ No need to replace network infrastructure. Dante AV works with already installed, cost-effective 1Gbps network gear.
    ■ Uses Dante Controller and endpoints so you can easily click to check video and audio control routing.

  • D20-EN-DE-UPDATE-1200

    Encoder/Decoder Configurable

    ■ D20 Series, D20H and D20S Dante AV transceiver can be configured as an individual encoder or decoder via a firmware update.
    ■ For a complete encode/decode solution, two separate devices are required,
    ■ Unique firmware to program as an encoder or decoder will be available on www.bolintechnology.com/downloadcenter

    ■ D20 Series, D20H and D20S Dante AV transceiver can be configured as an individual encoder or decoder via a firmware update.
    ■ For a complete encode/decode solution, two separate devices are required,
    ■ Unique firmware to program as an encoder or decoder will be available on www.bolintechnology.com/downloadcenter

  • Video Latency Test 1080p60-1600

    Lossless image with extremely low codec latency

    ■ Bolin’s D20 Series transceiver streams and transports up to 4K60 4:4:4 video output with ultra-low latency and lossless video quality.
    ■ D20 Series transceiver incorporates an optimized implementation of the popular JPEG2000 codec in FPGA, which delivers visually perfect lossless image at 4K60 with < 10ms codec latency.

    ■ Bolin’s D20 Series transceiver streams and transports up to 4K60 4:4:4 video output with ultra-low latency and lossless video quality.
    ■ D20 Series transceiver incorporates an optimized implementation of the popular JPEG2000 codec in FPGA, which delivers visually perfect lossless image at 4K60 with < 10ms codec latency.

  • IntoPIX JPEG2000

    intoPIX’s JPEG 2000 enables Dante AV to:

    ■ Create 4K multi-screen environments, allowing audio to be routed wherever desired
    ■ Deliver perfect lip-sync during live presentations with video thanks to ultra-low latency
    ■ Easily deploy and manage video walls at lower cost thanks to the utilization of Cat 5e cables and switchers
    ■ Simplify installation and use of conference rooms that combine video and audio media.
    Quoted from www.intopix.com

    ■ Create 4K multi-screen environments, allowing audio to be routed wherever desired
    ■ Deliver perfect lip-sync during live presentations with video thanks to ultra-low latency
    ■ Easily deploy and manage video walls at lower cost thanks to the utilization of Cat 5e cables and switchers
    ■ Simplify installation and use of conference rooms that combine video and audio media.
    Quoted from www.intopix.com

  • DanteAV 100% AV SYNC

    100% Synchronized video and audio

    D20 Series DanteAV transceiver has integrated Dante’s sub-microsecond synchronization to video and audio. Dante network clock keeps the camera video in sync regardless of the number of endpoints, making lip-sync problems a thing of the past.

    D20 Series DanteAV transceiver has integrated Dante’s sub-microsecond synchronization to video and audio. Dante network clock keeps the camera video in sync regardless of the number of endpoints, making lip-sync problems a thing of the past.

  • D20-EDID-2-1200

    HDMI output EDID and HDCP content protection supported

    ■ The D20 Series decoder provides decoded images via HDMI 2.0 port, with EDID support. Integrated high-performance scaling engine provides a scalable encoded source for a wide array of UHD and HD resolutions to match the different capabilities and requirements of sources, displays, codecs, and other equipment.
    ■ D20 Series encoder and decoder support HDCP 2.2 (HDCP 2.3 over the network) to provide digital content protection.

    ■ The D20 Series decoder provides decoded images via HDMI 2.0 port, with EDID support. Integrated high-performance scaling engine provides a scalable encoded source for a wide array of UHD and HD resolutions to match the different capabilities and requirements of sources, displays, codecs, and other equipment.
    ■ D20 Series encoder and decoder support HDCP 2.2 (HDCP 2.3 over the network) to provide digital content protection.

  • D20s-Dual Output

    HDMI and SDI Dual Output

    ■ In addition to HDMI 2.0 video output, D20S carries Bolin's video processor to simultaneously provide up to 12G-SDI output format for broadcast workflow use.

    ■ In addition to HDMI 2.0 video output, D20S carries Bolin's video processor to simultaneously provide up to 12G-SDI output format for broadcast workflow use.

  • DanteAV PTZ Camera Decoder Control

    Remote Control & Monitoring

    ■ D20 Series has a built-in serial (RS-422), which enables serial port PTZ camera joystick controller via Dante Serial Over IP control running Visca protocol. D20 Series also supports IR over IP feature to control connected displays, PTZ cameras, and other devices.
    ■ When paired with Bolin DanteAV PTZ camera D412/D220, D20 Series as a decoder supports camera control and configuration using Visca Over IP protocol from the PTZ controller.

    ■ D20 Series has a built-in serial (RS-422), which enables serial port PTZ camera joystick controller via Dante Serial Over IP control running Visca protocol. D20 Series also supports IR over IP feature to control connected displays, PTZ cameras, and other devices.
    ■ When paired with Bolin DanteAV PTZ camera D412/D220, D20 Series as a decoder supports camera control and configuration using Visca Over IP protocol from the PTZ controller.

Features

  • Unicast and Multicast for Video Display RoutingPaired with Dante AV decoder, it receives the signal from a DanteAV PTZ camera or an encoder and feeds it to a display device via the HDMI and/or 12G-SDI output. Using familiar Dante Controller software, the decoder can quickly and easily switch between multiple DanteAV endpoints including cameras or encoders on the network, with no need for breakouts or matrix switches to unicast or multicast display the video on any number of screens and video router system to use.
  • Implementation of HDCP 2.2 EncryptionAdheres to the latest HDCP 2.2 (HDCP 2.3 for network) specification for High-bandwidth Digital Content Protection. Allows protected content streams to pass between authenticated devices.
  • Dante Controller SupportedFull setup and control and monitoring of the device is enabled through Dante Controller that delivers standard Dante features such as automatic device discovery and system configuration, making network setup a simple plug and play experience.
  • Always Up To DateFirmware updates, upgrade via Bolin Dante AV software IP interface to keep the decoder features and performance up to date.
  • Audio Formats, Dante Audio over IPThe D20 Series Dante AV Transceiver supports Dante compatible networked audio streams from encoders and audio interfaces. The received Dante audio streaming can be combined with the video and then output via the HDMI output.
  • Two Ethernet Ports and POEThe D20 Series Dante AV Transceiver includes two RJ-45 1000BASE-T ports can be used to transport video over a Gigabit Ethernet network. Ports 1 for Dante network primary connection and Port 2 can be used to daisy-chain other endpoints. Port 1 is also capable of receiving power via POE++.
  • D20 Series Transceiver has two models: ■ D20H has HDMI 2.0 output only, which provides decoded image to output via HDMI 2.0. Integrated high-performance scaling engine provides scalable encoded source for a wide array of UHD, HD resolutions to match the different capabilities and requirements of sources, displays, codecs, and other equipment.
    ■ D20S has HDMI 2.0 and 12G-SDI output, which has SDI video processor built-in to provide SDI (Up to 12G-SDI) signal for ProAV and broadcast video work flow applications.
  • USB HID and USB OTGUSB control over IP that can be switched and routed alongside the AV signal or separately via a control system allows you to use a USB mouse and/or keyboard to control a remote computer via the Dante network. USB On The Go (OTG) for keyboard and mouse

Illustration

Specifications

Encoder/Decoder Device can be configured to operate as an encoder or a decoder via firmware/software upgrade. However, the device is not able to simultaneously operate as both an encoder and decoder.
Video Codec Optimized implementation of JPEG2000 codec in FPGA, Licensed By IntoPIX; Dante API management interface
Video Resolutions Up to 4096x2160@60Hz; RGB 4:4:4 @ 8 bit YCbCr 4:4:4 @ 8 bit YCbCr 4:2:2 @ 8/10/12 bit
Color Depth 8-bit, 10-bit, 12-bit
Audio Formats Dante Audio over IP
Bit Rates 200 to 800 Mbps
Video Streaming Unicast or Multicast
Copy Protection HDCP 2.2, HDCP 2.3 for network
Latency 0.5 frame (e.g. 2160p @ 60 Hz latency is < 8 ms between encoder and decoder), Note: Overall latency may increase depending on network configurations
Bandwidth 1 4kp60 10 bit 4:2:2; 500-600Mbps, results may vary depending on network configuration and management settings.
Bandwidth 2 1080p60 10 bit 4:2:2; 150-250Mbps, results may vary depending on network configuration and management settings.
Dante Ecosystem Friendly Instant Dante Ecosystem compatibility with existing Dante-enabled products; Unified control of audio and video using Dante tools - Dante Controller
When using the device as an encoder When using the device as an encoder
Available D20H, D20S
Format HDMI 2.0
General Built-in HDCP encryption/decryption for video; 800Mbps recommended maximum bit rate; Video transport formats: Dante Video over IP; HDR support; HDMI monitor output loop through
Supported Resolutions 4096x2160p, 3840x2160p, 1920x1080p, 1920x1200, 1600x1200, 1280x720, 1280x1024, 1024x768, 800x600, 720x576p, 720x480p, 640x480
Frame Rates (Hz) 23.98, 24, 25, 29.97, 30, 50, 59.94, 60
Colour Space RGB, YCbCr
Component Bit Width 8-bit, 10-bit, 12-bit
Colour Sub-Sampling 4:4:4, 4:2:2, 4:2:0
HDCP Copy Protection Yes
EDID YES
Monitor Ouput Looping from HDMI input video signal, above HDMI input video signal specification applies to Monitor Output Signal
HDMI Output (Decoder) Not active when in encode mode
SDI Output (Decoder) Not active when in encode mode
When using the device as a decoder When using the device as a decoder
Available D20H, D20S
Format HDMI 2.0
Supported Resolutions 4096x2160p, 3840x2160p, 1920x1080p, 1920x1200, 1600x1200, 1280x720p, 1280x1024, 1024x768, 800x600, 720x576p, 720x480p, 640x480
Frame Rates (Hz) 23.98, 24, 25, 29.97, 30, 50, 59.94, 60
Colour Space RGB, YCbCr
Component Bit Width 8-bit, 10-bit, 12-bit
Colour Sub-Sampling 4:4:4, 4:2:2, 4:2:0
HDCP Copy Protection HDCP 2.2
EDID YES, with D20H; No, with D20S
When using the device as a decoder When using the device as a decoder
Available D20S
Format 12G-SDI
Supported Resolutions 4096x2160p, 3840x2160p, 1920x1080p, 1920x1200, 1600x1200, 1280x720p, 1280x1024, 1024x768, 800x600, 720x576p, 720x480p, 640x480
Frame Rates (Hz) 23.98, 24, 25, 29.97, 30, 50, 59.94, 60
Colour Space YCbCr
Component Bit Width 8-bit, 10-bit, 12-bit
Colour Sub-Sampling 4:2:2, 4:2:0
Standard SMPTE 292(1.5Gb/s), SMPTE 424, SMPTE 425-A(3Gb/s), SMPTE 2081, SMPTE 2082 With SMPTE352 SDI Metadata Supported
HDCP Copy Protection SDI does not have output when the source video is HDCP content protected.
EDID No
Audio Transport Formats Up to eight channels at 44.1, 48, 88.2 or 96kHz. HDCP sourced audio channels limited to 48kHz.
Audio Transport Formats Dante Audio over IP
Audio Transport Formats HDMI 7.1 embedded audio.
Audio Transport Formats High-quality, low jitter with on-board clock generator for audio
Bit Depths 24, 16 and 32 bits per audio sample
Audio Input (Encoder) Embedded Audio over HDMI: Up to 8 channels to Dante
Audio Input (Encoder) Sample Rate: 32k to 192k, PCM24
Audio Input (Encoder) ASRC Conversion Range: 1:8 to 8:1
Audio Input (Encoder) ASRC Latency: 80 samples (1.6ms @ 48kHz)
Audio Output (Decoder) Embedded audio over HDMI output: 2 channels from DANTE
Audio Output (Decoder) Sample rate: 48K and 96K, PCM24
Audio Output (Decoder) Built-in 8-channel asynchronous sample rate converter
ETHERNET 1 POE Standard 1Gbps Ethernet, IEEE 802.3ab compliant 1000BASE-T Ethernet port, IEEE 802.3bt Type 3 compliant, PoE++ Class 6 (60W)
ETHERNET 2 Standard 1Gbps Ethernet, IEEE 802.3ab compliant 1000BASE-T Ethernet port
HDMI Input (Encoder only) HDMI 2.0 Type A connector, female; HDMI digital video/audio input
HDMI Monitor Output (Encoder only) HDMI 2.0 Type A connector, female; HDMI digital video/audio input
HDMI Output (Decoder only) HDMI 2.0 Type A connector, female; HDMI digital video/audio input
SDI Output (D20S) BNC, 75Ω,
USB 1, USB 2 (Decoder only) USB Type-A connector, female; USB signal extender port for connection to a mouse, keyboard; Available Power: 100 mA at 5 VDC.
USB OTG (On The Go) USB OTG Compliant, Host computer Mouse (Dante AV transmitter)
Serial Control RJ45, RS-422 compatible with Visca control PTZ camera
IR TX, IR RX 2-pin 3.5 mm, Carrier frequency:38 kHz; Supply voltage: 3.3V to 5V.
PTZ Camera IR Receiver Front and Back
LED Indicator Power, Codec, System, Error, Sync, HDCP
Power IEC60130-10 (JEITA standard RC-5320A) TYPE4 DC power connector; 12VDC 4A power input
Dante AV Powered By DanteAV Module
Network Interface Standard 1Gbps Ethernet
Audio Flow Audio Flow x 8 Flows / 8 Channels per Flow (unicast or multicast)
Video Flow Video Flow x 1 Flow / 1 Channel per Flow (unicast or multicast)
Time Stamp Hardware time-stamping, supporting sample-accurate playback
Power Consumption Power input @ 4K60: 40W (D20S); 28W (D20H)
PoE PoE++, IEEE 802.3bt Type 3, class 6 compliant
Power Adaptor Input: 1.5 A maximum @ 100-240 VAC, 50/60 Hz, Output: 4A @ 12 VDC; 12V DC IN has priority over Ethernet 1 POE. Ethernet 1 POE will become active a fraction of a second after 12V DC IN is disconnected.
Storage Temperature -40 to 100℃
Operating Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% (non-condensing)
Heat Dissipation Cooling fan speed adjustable, 3 Levels
Acoustic Noise NC35 or less, variable with cooling fan speed adjustment
Regulatory Compliance CE, FCC Part 15 Class B digital device
Body Color Metallic Black
Dimension 216.5x148.35x44mm (LxWxH)
Weight 2.5 lbs (1.3 kg)(Net weight)
Chassis Metal, black finish, heat dissipation surface, fan cooled; vented rear and sides
Mounting (Included) HDMI cable secure mount, surface mount for TV display, base mount.
Mounting (Optional) 19 inch single rack mount, 19 inch dual rack mount, Din rail mount

CompareCompare More Products

Check mark to compare different models or go to Compare Center to have more product comparison.

  • Maximum 4 compare products at once, please reselect.
  • Maximum 4 compare products at once, please reselect.
  • Maximum 4 compare products at once, please reselect.
Compare Now

ResourcesGo to Help & Download Center

Download product Datasheet and User Guide, click Go to Help & Download Center for more product information.

AAAArray ( [cameracontrol] => Array ( ) [faqandhowto] => Array ( ) [functionalityandperformance] => Array ( ) [productimages] => Array ( ) [productinformation] => Array ( [0] => Array ( [id] => 10217 [title] => Dante AV Encoder/Decoder (D20 Series Transceiver) Product Information [files] => Array ( [0] => Array ( [file_label] => D20 Series Dante AV Encoder/Decoder datasheet [file] => https://bolintechnology.com/wp-content/uploads/2021/06/Bolin-DanteAV-D20-Series-Transceiver-Datasheet-03112022.pdf [file_login] => [editor_login] => [file_show_in_detail] => 1 ) [1] => Array ( [file_label] => Dante AV D20 Series Transceiver Encoder/Decoder User Manual [file] => https://bolintechnology.com/wp-content/uploads/2021/06/Dante-AV-D20-Series-Transceiver-User-Manual-06192022-1.pdf [file_login] => 1 [editor_login] => [file_show_in_detail] => 1 ) ) [product_firmware] => [links] => [videos] => [images] => ) [1] => Array ( [id] => 10406 [title] => D20 Series Dante AV Transceiver Installation Information [files] => Array ( [0] => Array ( [file_label] => D Series Decoder Base and Surface Mount Installation [file] => https://bolintechnology.com/wp-content/uploads/2021/06/D-Series-Decoder-Base-and-Surface-Mount-Installation.pdf [file_login] => [editor_login] => [file_show_in_detail] => 1 ) [1] => Array ( [file_label] => B-DR10 Din Rail Mount installation [file] => https://bolintechnology.com/wp-content/uploads/2021/06/B-DR10-Din-Rail-Mount-installation.pdf [file_login] => [editor_login] => [file_show_in_detail] => 1 ) [2] => Array ( [file_label] => B-RM10 Single Rack Mount installation [file] => https://bolintechnology.com/wp-content/uploads/2021/06/B-RM10-Single-Rack-Mount-installation.pdf [file_login] => [editor_login] => [file_show_in_detail] => 1 ) [3] => Array ( [file_label] => B-RM11 Dual Rack Mount installation [file] => https://bolintechnology.com/wp-content/uploads/2021/06/B-RM11-Dual-Rack-Mount-installation.pdf [file_login] => [editor_login] => [file_show_in_detail] => 1 ) [4] => Array ( [file_label] => D20 Series Dante AV Transceiver D20H Dimension [file] => https://bolintechnology.com/wp-content/uploads/2021/06/D20-Series-Dante-AV-Transceiver-D20H-Dimension.pdf [file_login] => [editor_login] => [file_show_in_detail] => 1 ) [5] => Array ( [file_label] => D20 Series Dante AV Transceiver D20S Dimension [file] => https://bolintechnology.com/wp-content/uploads/2022/02/D20-Series-Dante-AV-Transceiver-D20S-Dimension.pdf [file_login] => [editor_login] => [file_show_in_detail] => 1 ) ) [product_firmware] => [links] => [videos] => [images] => ) ) [software] => Array ( [0] => Array ( [id] => 10512 [title] => D Series Dante AV D20S FW Upgrade – Dante AV Module [files] => [product_firmware] => Array ( [0] => Array ( [product_firmware_label] => D20S-Decoder FW: BL-D20S-D-PV-3.1.2.dnt [file] => Array ( [ID] => 10510 [id] => 10510 [title] => BL-D20S D-PV 3.1.2 [filename] => BL-D20S-D-PV-3.1.2.dnt [filesize] => 19545127 [url] => https://bolintechnology.com/wp-content/uploads/2022/06/BL-D20S-D-PV-3.1.2.dnt [link] => https://bolintechnology.com/?attachment_id=10510 [alt] => [author] => 18 [description] => [caption] => [name] => bl-d20s-d-pv-3-1-2 [status] => inherit [uploaded_to] => 10506 [date] => 2022-06-18 00:52:00 [modified] => 2022-06-18 00:52:00 [menu_order] => 0 [mime_type] => application/octet-stream [type] => application [subtype] => octet-stream [icon] => https://bolintechnology.com/wp-includes/images/media/default.png ) [has_another_file] => 1 [another_files_package] => Array ( [package_file_name] => Dante AV Decoder D20S FW Upgrade Package [read_me] => This package consists of the following files: It is important to upgrade all these firmware at this time to ensure having all improvements activated. 1) Use this firmware for upgrading D20S as a Decoder. 2) Product Version: BL-D20S-D-PV-3.1.2-1.dnt 3) Dante Firmware update Manager: DanteFirmwareUpdateManager-3.10.7.5_windows.zip 4) Dante-AV-Module-Firmware-Upgrade-User-Guide-12102021-3 5) This readme txt file From Bolin: The sole intention of this package is to provide a convenient upgrading service for our loyal customers. Due to the nature of our feature rich products, we require updating of various firmware files. For optimal operating experience, we sometimes may require all the files to be a certain version. These zip files exist to provide a one stop location for the device’s upgrade process to make sure proper files are used when multiple prerequisites are involved. The .exe files or zip files included within this package are either software tools needed or firmware itself, they are safe to use. Thank you for being a Bolin customer. [files] => Array ( [0] => Array ( [file] => Array ( [ID] => 10071 [id] => 10071 [title] => Dante-AV-Module-Firmware-Upgrade-User-Guide-06192022 [filename] => Dante-AV-Module-Firmware-Upgrade-User-Guide-06192022.pdf [filesize] => 524402 [url] => https://bolintechnology.com/wp-content/uploads/2021/06/Dante-AV-Module-Firmware-Upgrade-User-Guide-06192022.pdf [link] => https://bolintechnology.com/information_entity/d-series-dante-av-ptz-camera-d220-fw-upgrade-dante-av-module/dante-av-module-firmware-upgrade-user-guide-06192022/ [alt] => [author] => 2 [description] => [caption] => [name] => dante-av-module-firmware-upgrade-user-guide-06192022 [status] => inherit [uploaded_to] => 10020 [date] => 2022-06-20 03:00:10 [modified] => 2022-06-20 03:00:10 [menu_order] => 0 [mime_type] => application/pdf [type] => application [subtype] => pdf [icon] => https://bolintechnology.com/wp-includes/images/media/document.png ) ) [1] => Array ( [file] => Array ( [ID] => 10034 [id] => 10034 [title] => DanteFirmwareUpdateManager-3.10.7.5_windows [filename] => DanteFirmwareUpdateManager-3.10.7.5_windows.exe [filesize] => 54017072 [url] => https://bolintechnology.com/wp-content/uploads/2021/11/DanteFirmwareUpdateManager-3.10.7.5_windows.exe [link] => https://bolintechnology.com/information_entity/d-series-dante-av-ptz-camera-d220-fw-upgrade-dante-av-module/dantefirmwareupdatemanager-3-10-7-5_windows-2/ [alt] => [author] => 20 [description] => [caption] => [name] => dantefirmwareupdatemanager-3-10-7-5_windows-2 [status] => inherit [uploaded_to] => 10020 [date] => 2021-11-17 19:34:36 [modified] => 2021-11-17 19:42:56 [menu_order] => 0 [mime_type] => application/x-dosexec [type] => application [subtype] => x-dosexec [icon] => https://bolintechnology.com/wp-includes/images/media/default.png ) ) ) ) [log] =>

Improvements and Fixed:
1.Regular release

Supported device models:
D20S, Part Number: A101E002

Release Note:
1. Firmware BL-D20S-D-PV 3.1.2 is for using D20S as a Decoder.

[file_login] => 1 [editor_required] => [firmware_show_in_detail] => [create_date] => 2022/06/17 ) [1] => Array ( [product_firmware_label] => D20S-Encoder FW: BL-D20S-E-PV-3.1.2.dnt [file] => Array ( [ID] => 10511 [id] => 10511 [title] => BL-D20S E-PV 3.1.2 [filename] => BL-D20S-E-PV-3.1.2.dnt [filesize] => 19630847 [url] => https://bolintechnology.com/wp-content/uploads/2022/06/BL-D20S-E-PV-3.1.2.dnt [link] => https://bolintechnology.com/?attachment_id=10511 [alt] => [author] => 18 [description] => [caption] => [name] => bl-d20s-e-pv-3-1-2 [status] => inherit [uploaded_to] => 10506 [date] => 2022-06-18 00:52:28 [modified] => 2022-06-18 00:52:28 [menu_order] => 0 [mime_type] => application/octet-stream [type] => application [subtype] => octet-stream [icon] => https://bolintechnology.com/wp-includes/images/media/default.png ) [has_another_file] => 1 [another_files_package] => Array ( [package_file_name] => Dante AV Encoder D20S FW Upgrade Package [read_me] => This package consists of the following files: It is important to upgrade all these firmware at this time to ensure having all improvements activated. 1) Use this firmware for upgrading D20H as a Encoder. 2) Product Version: BL-D20S-E-PV-3.1.2-1.dnt 3) Dante Firmware update Manager: DanteFirmwareUpdateManager-3.10.7.5_windows.zip 4) Dante-AV-Module-Firmware-Upgrade-User-Guide-12102021-3 5) This readme txt file From Bolin: The sole intention of this package is to provide a convenient upgrading service for our loyal customers. Due to the nature of our feature rich products, we require updating of various firmware files. For optimal operating experience, we sometimes may require all the files to be a certain version. These zip files exist to provide a one stop location for the device’s upgrade process to make sure proper files are used when multiple prerequisites are involved. The .exe files or zip files included within this package are either software tools needed or firmware itself, they are safe to use. Thank you for being a Bolin customer. [files] => Array ( [0] => Array ( [file] => Array ( [ID] => 10071 [id] => 10071 [title] => Dante-AV-Module-Firmware-Upgrade-User-Guide-06192022 [filename] => Dante-AV-Module-Firmware-Upgrade-User-Guide-06192022.pdf [filesize] => 524402 [url] => https://bolintechnology.com/wp-content/uploads/2021/06/Dante-AV-Module-Firmware-Upgrade-User-Guide-06192022.pdf [link] => https://bolintechnology.com/information_entity/d-series-dante-av-ptz-camera-d220-fw-upgrade-dante-av-module/dante-av-module-firmware-upgrade-user-guide-06192022/ [alt] => [author] => 2 [description] => [caption] => [name] => dante-av-module-firmware-upgrade-user-guide-06192022 [status] => inherit [uploaded_to] => 10020 [date] => 2022-06-20 03:00:10 [modified] => 2022-06-20 03:00:10 [menu_order] => 0 [mime_type] => application/pdf [type] => application [subtype] => pdf [icon] => https://bolintechnology.com/wp-includes/images/media/document.png ) ) [1] => Array ( [file] => Array ( [ID] => 10034 [id] => 10034 [title] => DanteFirmwareUpdateManager-3.10.7.5_windows [filename] => DanteFirmwareUpdateManager-3.10.7.5_windows.exe [filesize] => 54017072 [url] => https://bolintechnology.com/wp-content/uploads/2021/11/DanteFirmwareUpdateManager-3.10.7.5_windows.exe [link] => https://bolintechnology.com/information_entity/d-series-dante-av-ptz-camera-d220-fw-upgrade-dante-av-module/dantefirmwareupdatemanager-3-10-7-5_windows-2/ [alt] => [author] => 20 [description] => [caption] => [name] => dantefirmwareupdatemanager-3-10-7-5_windows-2 [status] => inherit [uploaded_to] => 10020 [date] => 2021-11-17 19:34:36 [modified] => 2021-11-17 19:42:56 [menu_order] => 0 [mime_type] => application/x-dosexec [type] => application [subtype] => x-dosexec [icon] => https://bolintechnology.com/wp-includes/images/media/default.png ) ) ) ) [log] =>

Improvements and Fixed:
1.Regular release

Supported camera models:
D20S, Part Number: A101E002

Release Note:
1. Firmware BL-D20S-E-PV 3.1.2 is for using D20S as a Encoder

[file_login] => 1 [editor_required] => [firmware_show_in_detail] => [create_date] => 2022/06/17 ) ) [links] => [videos] => [images] => ) [1] => Array ( [id] => 8614 [title] => Firmware Upgrade Not Available [files] => [product_firmware] => [links] => [videos] => [images] => ) ) [videosignalandimage] => Array ( ) )

Order Information

Use Order Information for ordering cameras and accessories.

Item Number SKU Key Spec Note
A101E003 D20H HDMI 2.0 Output Body
A101E002 D20S HDMI 2.0 and 12G-SDI Output Body
L3030029 B-RM11 Dual Rack Mount Kit Accessory, Optional
L3030030 B-RM10 Single Rack Mount Kit Accessory, Optional
L3030031 B-DR10 Din Rail Mount Kit Accessory, Optional
B102E001 BL-PP97 97W High Power POE Power Supply Unit Accessory, Optional
L7030010 VCC-CC8MDP RS232 8-Pin Mini Din to Phoenix Adapter Accessory, Optional
L9190003 VCC-RC-2 IR Remote Controller Accessory, Optional
L9060003 VCC-P12-4 12VDC 4A Power Adapter What's included, X1
L7030005 VCC-CC45RS RS422/232 RJ45 Adapter What's included, X1
L3030032 B-SM10 Surface Mount Kit What's included, X1
L3030033 B-BM10 Base Mount kit What's included, X1
Thank you Card What's included, X1